<b id="qrjbt"><source id="qrjbt"><sub id="qrjbt"></sub></source></b>

  • <i id="qrjbt"></i>
    <blockquote id="qrjbt"><acronym id="qrjbt"><sub id="qrjbt"></sub></acronym></blockquote>
  • <xmp id="qrjbt"></xmp>
      <xmp id="qrjbt"></xmp>
  • Welcome to visitShenzhen Hangeng Electronics Co., Ltd.!

    About us|Contact us

    National 24-hour service hotline

    Company News Industry News
    Common power adapter damage reasons _ power adapter manufacturers
    time:2019-07-05 10:02        Click volume:【296 】Times

    With the popularity of personal smart mobile devices, power adapters have become one of the essential necessities of life. In daily use, the power adapter will be damaged. What are the common causes of power adapter damage?

    First: the output voltage is too high

    The output voltage is too high and generally comes from the regulated sampling and voltage regulation control circuit. In the closed control loop formed by DC output, sampling resistor, error sampling amplifier such as TL431, optocoupler, power control chip and other circuits, any one of the components will cause the output voltage to rise.

    The fuse is normal and no output voltage indicates that the switching power supply is not working or has entered the protection state. In the first step, check the value of the starting voltage of the starting pin of the power control chip. If there is no starting voltage or the starting voltage is too low, check whether the external components of the starting pin and the starting resistor are leaking. If the power control chip is normal, the fault can be quickly detected through the above monitoring. If there is a starting voltage, the output of the measurement control chip has a high or low transition at the instant of power-on. If there is no jump, it indicates that the control chip is damaged, the peripheral oscillation circuit component is damaged or the protection circuit is faulty, and the replacement control is performed. The chip, check the peripheral components, check one by one; if it is a jump, in most cases, the switch is defective or damaged.

    Second: line fault

    Line faults, including power cord damage, non-energization, poor contact contact oxidation, etc. Focus on checking whether the input and output lines are powered. If the line is faulty, you can solve it by replacing the power cord.

    The third type: insurance burned or blown up

    Mainly check the rectifier bridge, each diode, switch tube and large filter capacitors on 300 volts. This may cause the insurance to burn and blacken, or it may be caused by a problem with the anti-interference circuit. It is particularly noteworthy that the power supply control chip and the current sense resistor are usually burned out due to the breakdown of the switch tube. The thermistor is also easily burned out together with the insurance.

    Fourth: the output voltage is too low

    The following are the main reasons for the low output voltage:

    1. The performance of the switch tube is degraded, which causes the switch tube to fail to conduct normally, which increases the internal resistance of the power supply and reduces the load capacity.

    2. The 300V filter capacitor is poor, resulting in poor power supply load capacity, and the load output voltage will drop when connected.

    3, switching power supply load short-circuit fault (especially DC / DC converter short circuit or poor performance, etc.), at this time, first disconnect all the load of the switching power supply circuit, check whether the switching power supply circuit fault or the load circuit is faulty. If the load circuit is disconnected and the voltage output is normal, it means that the load is too heavy; or it is still not normal, indicating that the switching power supply circuit is faulty.

    4. The switching transformer is not good, which not only causes the output voltage to drop, but also causes the switching tube to be insufficiently excited to damage the switching tube, the output voltage terminal filter capacitor or the rectifier diode failure, etc., which can be judged by the replacement method.

    Copyright?Shenzhen Hangeng Electronics Co., Ltd. PC version | Mobile version Technical support: Jun domain network construction 粵ICP備2021088171號
    Leave a message now, no need to wait!

    Receive your message, we will get in touch with you in the first time

    美女直播黄色大片 日日摸夜夜摸狠狠摸流水 免费在线视频中文字幕 欧美成aⅴ人片
    在线看福利毛片 黄色=及片 在线播放国产不卡免费香蕉 亚洲欧美视频 下载 超碰天天做天天天天爱三级